Vyšetřování tribologických vlastností tenkých vrstev
| dc.contributor.advisor | Soukup Zbyněk, Ing. Ph.D. | cs |
| dc.contributor.author | Pádecký, Lukáš | cs |
| dc.contributor.referee | Čerstvý Radomír, Ing. Ph.D. | cs |
| dc.date.accepted | 2025-08-26 | |
| dc.date.accessioned | 2026-02-21T18:03:25Z | |
| dc.date.available | 2024-10-15 | |
| dc.date.available | 2026-02-21T18:03:25Z | |
| dc.date.issued | 2025-07-11 | |
| dc.date.submitted | 2025-07-11 | |
| dc.description.abstract | V této práci byly studovány tribologické vlastnosti tenkých vrstev, konkrétně DLC vrstev dopovaných N2. Hlavním cílem bylo sledovat závislosti těchto vlastností na obsahu N2, zatěžovací síle a relativní vlhkosti prostředí v komoře. Měřenými a vyhodnocovanými parametry byly koeficient tření, otěr tenké vrstvy a otěr protikusu (kuličky). S rostoucím obsahem N2 se koeficient tření nejprve zvyšoval, přičemž maxima dosahoval při podílu 1 % N2, a poté klesal. Podobný trend byl pozorován i u otěru kuličky. Naproti tomu otěr samotné tenké vrstvy s rostoucím obsahem N kontinuálně rostl. Při zvyšování zatížení docházelo nejprve k poklesu koeficientu tření, následovanému opětovným nárůstem. Otěr kuličky i vrstvy naopak nejprve rostl a následně klesal. Relativní vlhkost vzduchu měla rovněž výrazný vliv - koeficient tření s rostoucí vlhkostí nejprve rostl, poté klesal. Otěr vrstvy se při zvyšující se vlhkosti nejprve snižoval a poté zvyšoval, zatímco otěr kuličky se zvyšoval po celou dobu. | cs |
| dc.description.abstract-translated | In this thesis, the tribological properties of thin films were investigated, with a focus on nitrogen-doped diamond-like carbon (DLC) coatings. The aim was to examine how these properties are influenced by the nitrogen content in the deposition process, the applied load, and the relative humidity in the testing chamber. The measured and evaluated parameters included the coefficient of friction, wear of the thin film, and wear of the counterbody (ball). With increasing nitrogen content, the coefficient of friction initially increased, reaching its maximum at 1 % N, and then decreased. A similar trend was observed for the wear of the ball. In contrast, the wear of the thin film increased continuously with higher nitrogen concentrations. As the applied load increased, the coefficient of friction first decreased and then increased again. The wear of both the ball and the thin film showed the opposite trend increasing initially and then decreasing at higher loads. Relative humidity was also found to have a significant effect. The coefficient of friction increased at first with rising humidity and then decreased. The wear of the thin film initially decreased and later increased, while the wear of the ball continuously increased throughout the range of tested humidity level. | en |
| dc.description.department | Katedra fyziky | cs |
| dc.description.result | Obhájeno | cs |
| dc.format | 41 s. | |
| dc.identifier | 100815 | |
| dc.identifier.uri | http://hdl.handle.net/11025/66627 | |
| dc.language.iso | cs | |
| dc.publisher | Západočeská univerzita v Plzni | cs |
| dc.rights | Plný text práce je přístupný bez omezení | cs |
| dc.rights.access | openAccess | cs |
| dc.subject | tenké vrstvy | cs |
| dc.subject | tribologie | cs |
| dc.subject | fyzika | cs |
| dc.subject | DLC vrstvy | cs |
| dc.subject | naprašování | cs |
| dc.subject | dopování dusíkem | cs |
| dc.subject | koeficient tření | cs |
| dc.subject | otěr | cs |
| dc.subject | zátěž | cs |
| dc.subject | relativní vlhkost | cs |
| dc.subject | tření | cs |
| dc.subject.translated | thin films | en |
| dc.subject.translated | tribology | en |
| dc.subject.translated | DLC films | en |
| dc.subject.translated | sputtering | en |
| dc.subject.translated | nitrogen doping | en |
| dc.subject.translated | coefficient of friction | en |
| dc.subject.translated | wear | en |
| dc.subject.translated | load | en |
| dc.subject.translated | relative humidity | en |
| dc.subject.translated | friction | en |
| dc.thesis.degree-grantor | Západočeská univerzita v Plzni. Fakulta aplikovaných věd | cs |
| dc.thesis.degree-level | Bakalářský | cs |
| dc.thesis.degree-name | Bc. | cs |
| dc.thesis.degree-program | Aplikovaná fyzika a fyzikální inženýrství | cs |
| dc.title | Vyšetřování tribologických vlastností tenkých vrstev | cs |
| dc.type | bakalářská práce | cs |
| local.files.count | 4 | * |
| local.files.size | 2447803 | * |
| local.has.files | yes | * |
| local.relation.IS | https://portal.zcu.cz/StagPortletsJSR168/CleanUrl?urlid=prohlizeni-prace-detail&praceIdno=100815 |
Files
Original bundle
1 - 4 out of 4 results
No Thumbnail Available
- Name:
- BP_Padecky_A22B0003P.pdf
- Size:
- 1.84 MB
- Format:
- Adobe Portable Document Format
- Description:
- VŠKP
No Thumbnail Available
- Name:
- PV_Padecky_A22B0003P.pdf
- Size:
- 418.32 KB
- Format:
- Adobe Portable Document Format
- Description:
- Posudek vedoucího VŠKP
No Thumbnail Available
- Name:
- PO_Padecky_A22B0003P.pdf
- Size:
- 53.77 KB
- Format:
- Adobe Portable Document Format
- Description:
- Posudek oponenta VŠKP
No Thumbnail Available
- Name:
- PB_Padecky_A22B0003P_generated_by_STAG.pdf
- Size:
- 38.81 KB
- Format:
- Adobe Portable Document Format
- Description:
- Průběh obhajoby VŠKP